![sonance invisible series sonance invisible series](https://www.spireintegrated.com/wp-content/uploads/2018/06/In-Wall___In-Ceiling_2_Top_Parallax.jpg)
- Sonance invisible series install#
- Sonance invisible series manual#
- Sonance invisible series professional#
- Sonance invisible series series#
Select an amplifier with max RMS watts per channel at 4 ohms that closely matches or is less than the IS speaker’s rated power handling (see page 16). NOTE: Pay attention to Sonance IS speaker-rated RMS power handling. Never run more than two Invisible Speakers in parallel on one amplifier channel. Sonance DSP Amplifiers are rated down to 4 Ohms and are stable to 2 Ohms. Preconfigured curves for various finish types and thicknesses allow for effortless calibration without the need for additional
Sonance invisible series series#
These amps have preloaded curves to optimize the performance of Invisible Series speakers and woofers. When using the IS6T in 70V/100V, we recommend the Sonance DSP-2-750 MKII. Sonance DSP Amplifiers are recommended for use with the IS6T speaker. If necessary, re-select a lower or higher tap setting.
![sonance invisible series sonance invisible series](https://www.taxivision.it/wp-content/uploads/2020/06/sonance-invisible-series-diffusori-torino.jpg)
After selecting a given tap, play the speaker with an actual audio signal to verify the speaker provides adequate volume. WARNING: Do not mount and finish over the speaker until you have selected the necessary tap setting to achieve the desired volume level. We strongly recommend testing the system with music to determine the correct output level. Using a flat-head screwdriver set the transformer tap to the correct tap setting for your installation.When using conduit attach the conduit connector to the terminal cover plate then connect the wires to the terminal block being certain to connect the positive wire to the terminal marked + and the negative wire to the terminal marked –. Connect the wires to the terminal block being certain to connect the positive wire to the terminal marked + and the negative wire to the terminal marked –. The wire needs to be clamped as required by national or local codes. When using speaker wire without conduit, run the wire through the hole on the terminal cover plate.Using a #2 Phillips head screwdriver remove the two screws securing the terminal cover plate.The Sonance Invisible Series IS6T includes a 70V/100V Sonance Laminated Core Transformer with an adjustable tap. Per-transducer poly fuses integrated into every speaker allow extra protection of each transducer from over-current.Integrated, sealed metal rear enclosure for consistent installs in commercial applications.Embedded depth discs allow the installer to verify the finish material thickness with the optional DG-1 DISC System Depth Gauge (SKU 93491).30W multi-tap 70V/100V transformer with 4-ohm bypass and Sonance Laminated Core Technology for full-range, high-fidelity audio reproduction.
![sonance invisible series sonance invisible series](https://www.installason.fr/wp-content/uploads/2020/02/sonance-ISW.jpg)
Finish-up-to or finish-over with up to 1/8” (3mm) flexible topping compound or finish material.
![sonance invisible series sonance invisible series](http://www.avsimplifiedsolutions.com/wp-content/uploads/2016/12/maxresdefault.jpg)
Supply your own shims for thicker substrates
Sonance invisible series install#
Do not install near a heat source such as radiators, heat registers, stoves, fireplaces, or other apparatus (including amplifiers) that produce heat.Install in accordance with the manufacturer’s instructions. Do not block any ventilation openings.Consult a local authority for specific requirements, regulations, and building codes of the jurisdiction in which this product is to be installed. It is the installer’s responsibility to ensure this product is installed in accordance with local building codes and regulations.
Sonance invisible series manual#
This product manual is intended to serve as a general guideline for most applications.
Sonance invisible series professional#
This product is intended to be installed by professional AV integrators and installers only.